Advanced Protection

Submersible Turbine Pumps

Available as a factory installed option on STPAG and IST biofuel compatible submersible turbine pumps, Advanced Protection defends STPs from accelerated corrosion caused by the acetic byproduct of microbial activity.

Ordering Guide

A typical turbine model designation has up to five components to define the pump being supplied as follows:

STP XXXXX Y-A-B

  • STP = Basic Model Designation (IST for variable speed models)
  • XXXXX = Factory Installed Options (Model designations may include one or more of the following characters in alphabetical order.)
  • AP = Advanced protection with coated exterior cast surfaces, stainless steel fasteners and piping, alcohol-gasoline compatible)
  • F = Floating suction adapter (1½" NPT female adapter)
  • H = High pressure deadhead output (150 and 200 models only)
  • K = Intake filter screen (IFS, factory installed to PMA)
  • M = MagShell™ (flow enhancing, expanded PMA shell)
  • R = Model R check valve (24 psi relief/22 psi reset for PLLD)*
  • W = Model W check valve (16 psi relief/13 psi reset for PPM4000)*
  • Y = Pump Motor Horsepower Rating
  • 33 = 1/3 hp fixed speed
  • 75 = ¾ hp fixed speed
  • 150 = 1½ hp fixed speed
  • 200 = 2 hp fixed speed
  • VS2 = 2 hp variable speed**
  • VS4 = 4 hp variable speed***
  • A = Model Length
  • VL1 = Variable length range #1
  • VL2 = Variable length range #2
  • VL3 = Variable length range #3
  • B = Riser Pipe Length
  • Riser pipe length is expressed as two numeric characters that indicate the total length of the riser in inches. Riser pipes are available from 7" to 60" in 1" increments (additional charge for risers 31" or longer).
  • *If not otherwise specified, all STP models are supplied with standard model check valve (40 psi relief /35 psi reset for MLD, TS-LS300, and TS-LS500).
  • **Implied on IST models unless VS4 is specified.
  • *** IST models only.

Advanced Protection Submersible Turbine Pumps

Model

Description

Model Length Range*

ISTAPMVS4-VL1

4 hp AP variable speed with MagShell™

64"-92"

ISTAPMVS4-VL2

4 hp AP variable speed with MagShell™

95"-156"

ISTAPMVS4-VL3

4 hp AP variable speed with MagShell™

127"-218"

ISTAPM-1

2 hp AP variable speed with MagShell™

59"-87"

ISTAPM-2

2 hp AP variable speed with MagShell™

90"-151"

ISTAPM-3

2 hp AP variable speed with MagShell™

122"-213"

STPAPM200-VL1

2 hp AP fixed speed with MagShell™

63"-91"

STPAPM200-VL2

2 hp AP fixed speed with MagShell™

94"-154"

STPAPM200-VL3

2 hp AP fixed speed with MagShell™

126"-217"

STPAPHM200-VL1

2 hp AP high pressure fixed speed with MagShell™

63"-92"

STPAPHM200-VL2

2 hp AP high pressure fixed speed with MagShell™

94"-155"

STPAPHM200-VL3

2 hp AP high pressure fixed speed with MagShell™

126"-218"

STPAP150-VL1

1-1/2 hp AP fixed speed

60"-88"

STPAP150-VL2

1-1/2 hp AP fixed speed

91"-152"

STPAP150-VL3

1-1/2 hp AP fixed speed

123"-214"

STPAPH150-VL1

1-1/2 hp AP high pressure fixed speed

61"-89"

STPAPH150-VL2

1-1/2 hp AP high pressure fixed speed

92"-152"

STPAPH150-VL3

1-1/2 hp AP high pressure fixed speed

124"-215"

STPAP75-VL1

3/4 hp AP fixed speed

57"-86"

STPAP75-VL2

3/4 hp AP fixed speed

88"-149"

STPAP75-VL3

3/4 hp AP fixed speed

120"-212"

  • 1. Remove “M” from model number for non-MagShell™ pump motor assembly (where applicable).
  • 2. STPAP/ISTAP models are listed for compatibility with fuel mixtures containing diesel fuel with up to 20% biodiesel, 100% biodiesel, up to 85% ethanol wiht gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.
  • 3. All models are supplied with a standard check valve unless factory option “R” or “W” is specified.
  • 4. All above ISTAP models can only be powered by a MagVFC™. 4 hp models require three-phase incoming power supply, 2 hp models can be supplied with single- or three-phase incoming power.
  • 5. All above STPAP models require single-phase, 208-230 VAC, 60 Hz incoming power.
  • 6. 4" riser pipe, if supplied locally, must be 4½" OD by 3/16" WT tubing.
  • 7. For riser pipe lengths 31" to 60", adder charge applies.
  • *Model length (A) defined as the dimension from the turbine manifold bottom to the pump motor inlet

Factory Installed Options

Model

Description

F

Floating suction adapter, 1½" NPT female, must be factory installed

K

IFS (intake filter screen) factory assembled to pump motor assembly

R

Model R check valve, factory installed, for Veeder-Root™ PLLD Line Leak

W

Model W check valve, factory installed, for Red Jacket PPM4000 Line Leak

Field Installed Options

Model

Description

5874202800

MagVFC™, 2 hp or 4 hp variable frequency controller, one required per IST

400137908

Syphon check valve (when ordered with STP)

400818921

STP-CBS, single-phase control box with lockout switch, 110 Volt coil

402312921

STP-DHI-SCI, combo DHI with factory wired STP-SCI (when purchased with a 4" STP)*

402312921

STP-DHI-SCI, combo DHI with factory wired STP-SCI (when purchased without a 4" STP)

402313921

STP-DHI-CBS, combo DHI with factory wired STP-CBS

402459931

Model 65 psi check valve (for slave of manifolded STPs with Veeder-Root™ PLLD)

402507930

Secondary syphon kit (when two syphon primes are required for one STP)

5800100215

STP-SCI, single-phase smart controller (when purchased without a 4" STP)

5800100215

STP-SCI, single-phase smart controller (when purchased with a 4" STP)*

5800300100

STP-DHI, dispenser hook isolation for 110 Volt dispenser handle switches, up to eight each

  • *When purchasing STP-SCI or STP-DHI-SCI in equal quantities of fixed speed 4" STPs, the STP-SCI or STP-DHI-SCI will be invoiced at special discount pricing.

 

Add Quotation